Precision presses and precision punch of the structure

punch of the structure High-speed punch on the mold is the upper part of the entire sub-dies, that is installed in the press slide on the die part. The upper die seat is the uppermost plate-like part of the upper die. The workpiece is pressed against the press slide and fixed by the mold handle or directly with the press slide. The lower die is the lower part of the entire sub-die, that is installed in the press work on the table part of the die. The lower mold seat is the bottom part of the lower mold plate parts, working directly in the press work table or pad. The blade wall is a side wall for punching the edge of the die hole. The edge slope is the slope of each side of the punch die wall. Air cushion is compressed air as the driving force of the top bomb. Refer to the ‘Top Bouncer’. The backside clamp is a part that supports the one-way force punch from the other side of the working face. High-speed punch guide sleeve is for the upper and lower die seat relative movement to provide precision-oriented tubular parts, the majority of fixed in the mold base bus bar bender, and fixed in the lower die seat with the use of the guide column. The guide plate is a plate-like part with an inner hole in which the punch is precisely slid, and is used for ensuring the mutual alignment of the punch and the die and for discharging. Pillar is for the upper and lower die holder relative movement to provide precision-oriented cylindrical parts, the majority of fixed in the lower die seat, and fixed to the die set with the guide sleeve used. Pilot pin is inserted into the hole in the material guide its position in the mold-shaped parts of the pin. The guide plate mold is guided by the guide plate, the punch is not separated from the guide plate when the mold is used. The guide plate is a plate-like guide member for guiding the strip material into the die. The guide column mold frame is the guide column, guide sleeve sliding mold. High-speed punching die is installed in the press for the production of punching process equipment, by the interaction of the upper and lower parts. Punch is the punch from the punch directly formed by the role of convex-shaped working parts, that is, the work surface to the shape of the parts. Die is the punch from the punch directly formed by the role of the concave part of the work, that is, the shape of the work surface for the parts. A protective plate is a plate-like part that prevents the finger or foreign object from entering the dangerous area of ​​the die. Compression plate is used in the stamping die for pressing materials or process parts to control the flow of material parts, drawing die, the majority of pressure plate called the binder circle. Binder is drawing die or drawing die to control the flow of materials to control the rib-shaped protrusions, the binder can be concave die or billet of the local structure, can also be set in the die or pressure circle Individual parts. The pressure sill is a section of the rectangle of the special binder. See ‘Binder’. The bearing plate is used to connect the long die on the plane, supporting the stamping material plate parts angle shear. A continuous die is a die having two or more stations, and the material is fed one station at a time along the stroke of the press so that the punch is gradually formed. High-speed punch side edge is cut in the strip side of the feed material positioning notch punch. The side pressing plate is a plate-like member which applies pressure to one side of the strip through the spring to urge the other side thereof against the sheet. The ejector rod is a rod-like member which is pushed upward or upwardly to directly push the workpiece or the preform. The top plate is a plate-like part that moves in the die or module to push the workpiece or scrap directly or indirectly upwards. The ring gear is a ring-shaped tooth-shaped protuberance on a fine blanking die or a belt press plate and is a partial structure of a die or a belt blanking plate rather than a separate part. Limit sleeve is used to limit the minimum die height of the tubular parts, usually set in the guide column outside.

The limit post is a cylindrical member which limits the minimum closing height of the die. Locating pin is to ensure that the process components in the mold has a constant position of the parts, its shape is called a positioning pin or positioning plate. High-speed punch plate is fixed plate fixed parts. Fixed discharge plate is fixed in the die position on the unloading plate. The fixed stop pin is a retaining pin that is fixed in the mold. The unloader is a non-plate-like part or device that releases the workpiece from the outer surface of the punch custom cnc machine. A stripper plate is a fixed or movable plate-shaped part that releases material or workpieces from a punch. Unloading plate is sometimes made with the guide plate integrated, and from the role of lead material, still known as the discharge plate. A discharge screw is a screw that is fixed to the relief stripper plate and serves to limit the rest position of the discharge stripper plate. High-speed punch single-mode die in the press is only one stroke to complete a process dies. There are two types of waste cutters. 1. Cutter mounted on the flange flange trimming die for cutting the whole edge trimming scrap for easy removal. 2. A cutter mounted on a press or die for cutting a strip of waste material at a fixed length for easy removal. Combination die is formed by the geometric elements of the progressive vice by the various pieces of common, adjustable sets of dies. Plane shape of the outline of the general need to punch a few sub-combination of sub-punching. Stopper pins are used to position the material at the beginning of the material. Before the block with the material are mobile. Piece is composed of a complete die, punch, stripper plate or fixed plate and other pieces of the various parts. The stopper is a hardened part for positioning the material to be cut out through the side cutting edge and for balancing the one-side cutting force suffered by the side edge. The stopper is generally used in conjunction with the side edge.

Leave a Reply

XHTML: You can use these tags: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>